Numerical and Experimental Investigation of Deep Drawing Process in Square Section of Single-Layer and Two-Layer Sheet

Document Type : Research Paper

Authors

1 Mechanical Engineering, Tafresh University, Tafresh, Iran

2 Mechanical Engineering Department, Tafresh University, Tafresh, Iran

3 Department of Mechanical Engineering, Faculty of Engineering, Arak University, Arak, Iran

Abstract

Deep drawing of two-layer sheet is a suitable way to achieve product with a desired shape and desired properties in sheet metal forming technology. Control of deep drawing parameter such as thinning is the most important challenge in this process. The most difficult part of this challenge is differences in material properties and geometry of each layer. In this paper, numerical approach has been exploited to plan and control of two layer deep drawing process. For this purpose, the three-dimensional (3D) finite element has been used. ST14– Al1100 (A.I. and S.I. lay-up) were selected as materials of two layer sheet metal. The results of simulation have been validated with experiments. Based on numerical study, effect of process parameters on the percentage of thinning, maximum plastic strain, rupture, required forming force and blank holder force (BHF) has been studied. This study has also been done on one-layer sheet metal and differences between deep drawing of one-layer and two-layer sheets have been comprehensively investigated. The results showed that maximum thinning is occurred in the upper layer of die radial region as well as in the lower layer of punch radial region. Also, the maximum equivalent plastic strain in the lower layer is more than the maximum of equivalent plastic strain in the upper layer.

Keywords


[1] F. W. Hosford, R. M. Caddell, Metal forming: mechanics and metallurgy, Cambridge University Press, (2011) 225-228.
[2] M. Safari, M. Farzin, H. Mostaan, A novel method for laser forming of two-step bending of a dome shaped part, Iranian Journal of Materials Forming 4(2) (2017) 1-14.
[3] M. Safari, Two Point Incremental Forming of a Complicated Shape with Negative and Positive Dies, Iranian Journal of Materials Forming 4(2) (201751-61.
[4] M. Sheykholeslami, S. Cinquemani, S. Mazdak, Numerical study of the of ultrasonic vibration in deep drawing process of circular sections with rubber die. In Active and Passive Smart Structures and Integrated Systems XII, International Society for Optics and Photonics 10595 (2018) 539.
[5] S. Kathiravan, A. N. Sait, M. Ravichandran, Experimental Investigation on Stretchability of an Austentic Stainless Steel 316L, Iranian Journal of Materials Forming 3(1) (2016) 55-64.
[6] H. Vafaeenezhad, S.H. Seyedein, M.R. Aboutalebi, A. R. Eivani, Workability Study in Near-Peritectic Sn-5% Sb Lead-Free Solder Alloy Processed by Severe Plastic Deformation, Iranian Journal of Materials Forming 3(2) (2016) 39-51
[7] M.R. Morovvati, A. Fatemi, M. Sadighi, Experimental and finite element investigation on wrinkling of circular single layer and two-layer sheet metals in deep drawing process, The International Journal of Advanced Manufacturing Technology 54(1) (2011) 113-121.
[8] A. G. Mamalis, D. E. Manolakos, A. K. Baldoukas, Simulation of sheet metal forming using explicit finite-element techniques: effect of material and forming characteristics: part 1. Deep-drawing of cylindrical cups, Journal of materials processing technology 72(1) (1997) 48-60.
[9] A. G. Mamalis, D. E. Manolakos, A. K. Baldoukas, Simulation of sheet metal forming using explicit finite element techniques: effect of material and forming characteristics: Part 2. Deep-drawing of square cups, Journal of Materials processing technology 72(1) (1997) 110-116.
[10] P. Mohammad Habibi, K. Yamaguchi, N. Takakura, Redrawing analysis of aluminum–stainless-steel laminated sheet using FEM simulations and experiments, International journal of mechanical sciences 43(10) (2001) 2331-2347.
[11] M. T. Browne, M. T. Hillary, Optimizing the variables when deep-drawing CR 1 cups, Journal of materials processing technology 136(1) (2003) 64-71.
[12] S. Çağlar, A. Erman Tekkaya, C. Hakan Gür, Comparison of the deepdrawability of aluminum and steel using numerical simulation experiments, AIP Conference Proceedings 778(1) AIP (2005).
[13] F. Fereshteh-Saniee, A. Alavi-Nia, A. Atrian-Afyani, An experimental investigation on the deep drawing process of steel–brass bimetal sheets. Proceedings of metal forming. Krakow, Poland, Conference, Conference. (2008) 63-70
[14] Aghchai, A. Jalali, M. Shakeri, B. Mollaei-Dariani, Theoretical and experimental formability study of two-layer metallic sheet (Al1100/St12), Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 222(9) (2008) 1131-1138.
[15] S. Raju, G. Ganesan, R. Karthikeyan, Influence of variables in deep drawing of AA 6061 sheet, Transactions of Nonferrous Metals Society of China 20(10) (2010) 1856-1862.
[16] H. Li, J. Chen, J. Yang, Experiment and numerical simulation on delamination during the laminated steel sheet forming processes, International Journal of Advanced Manufacturing Technology 68 (2013).
[17] A. Atrian, F. Fereshteh-Saniee, Deep drawing process of steel/brass laminated sheets, Composites Part B: Engineering 47 (2013) 75-81.
[18] R. Safdarian, M.J. Torkamany, A Novel Approach for Formability Prediction of Tailor Welded Blank, Iranian Journal of Materials Forming 3(2) (2016) 1-12
[19] H. Deilami Azodi, R. Darabi, A Comparative Study on the Formability Prediction of two-layer metallic Sheets, Iranian Journal of Materials Forming 4(1) (2017) 39-51.
[20] M. Mahmoodi, H. Sohrabi, Using the Taguchi Method for Experimental and Numerical Investigations on the Square-Cup Deep-Drawing Process for Aluminum/Steel Laminated Sheets, Mechanics of Advanced Composite Structures 4(2) (2017) 169-177.