Influence of High Strain Rates on the Mechanical Behavior of High-Manganese Steels

Document Type : Research Paper

Author

Department of Materials Engineering, Shiraz Branch, Islamic Azad University, Shiraz, Iran

Abstract

In this work, dynamic mechanical properties of three high-manganese steels with TRIP/TWIP or fully TWIP characteristics are studied. High strain rate experiments in the range of true strain rates between ~500 and 1800 /s are conducted using a dynamic torsional testing setup. All the three steels show a positive strain rate sensitivity in the intermediate range of strain rates (up to 500 /s). But, they behave differently as the strain rate is further increased. The steel with the lowest carbon content shows a strain rate softening behavior, while the other two exhibit strain rate hardening. The adiabatic temperature rise of the material greatly influences its stacking fault energy during the high rate dynamic deformation. Thus, unlike the quasi-static experiments, the dominant deformation mechanism of the steel during a dynamic test changes as the deformation progresses. In this regard, the variations of the stacking fault energy during the deformation are calculated for the three steels.

Keywords


[1]
A. S. Khan, M. Baig, S. H. Choi, H. S. Yang and X. Sun, Quasi-static and dynamic responses of advanced high strength steels: Experiments and modeling, International Journal of Plasticity, 30-31 (2012) 1-17.
[2]
R. Kuziak, R. Kawalla and S. Waengler, Advanced high strength steels for automotive industry, Archives of Civil and Mechanical Engineering, 8 (2008) 103-117.
[3]
V. J. Slycken, P. Verleysen, J. Degrieck, J. Bouquerel and B. C. De Cooman, Dynamic response of aluminum containing TRIP steel and its constituent phases, Material Science and Engineering A, 460–461 (2007) 516–524.
[4]
R. E. Schramm and R. P. Reed, Stacking fault energies of seven commercial austenitic stainless steels, Metallurgical Transactions A, 6 (1975) 1345-1351.
[5]
S. Allain, J. P. Chateau, O. Bouaziz, S. Migot and N. Guelton, Correlations between the calculated stacking fault energy and the plasticity mechanisms in Fe–Mn–C alloys, Materials Science and Engineering A, 387–389 (2004) 158-162.
[6]
A. Dumay, J. P. Chateau, S. Allain, S. Migot and O. Bouaziz, Influence of addition elements on the stacking-fault energy and mechanical properties of an austenitic Fe–Mn–C steel, Materials Science and Engineering A, 483–484 (2008) 184-187.
[7]
O. Bouaziz, S. Allain, C. P. Scott, P. Cugy and D. Barbier, High manganese austenitic twinning induced plasticity steels: A review of the microstructure properties relationships, Current Opinion in Solid State and Materials Science, 15 (2011) 141–168.
[8]
L. Remy, Kinetics of f.c.c. deformation twinning and its relationship to stress-strain behaviour, Acta Metallurgica, 26 (1978) 443-451.
[9]
T. A. Lebedkina, M. A. Lebyodkin, J. P. Chateau, A. Jacques and S. Allain, On the mechanism of unstable plastic flow in an austenitic FeMnC TWIP steel, Materials Science and Engineering A, 519 (2009) 147–154.
[10]
K. Chung, K. Ahn, D. H. Yoo, K. H. Chung, M. H. Seo and S. H. Park, Formability of TWIP (twinning induced plasticity) automotive sheets, International Journal of Plasticity, 27 (2011) 52–81.
[11]
T. George, Classic Split-Hopkinson Pressure Bar Testing, in ASM Handbook, Vol. 8, Mechanical Testing and Evaluation, ASM International, Materials Park, Ohio, 2000, pp.1027-1068.
[12]
O. Grassel, L. Kruger, G. Frommeyer and L. W. Meyer, High strength Fe-Mn-(Al, Si) TRIP/TWIP steels development-properties-application, International Journal of Plasticity, 16 (2000) 1391-1409.
[13]
P. Sahu, S. Curtze, A. Das, B. Mahato, V. T. Kuokkala and S. G. Chowdhury, Stability of austenite and quasi-adiabatic heating during high strain-rate deformation of twinning-induced plasticity steels, Scripta Materialia, 62 (2010) 5–8.
 
[14]
A. Soulami, K. S. Choi, Y. F. Shen, W. N. Liu, X. Sun and M. A. Khaleel, On deformation twinning in a 17.5% Mn–TWIP steel: A physically based phenomenological model, Materials Science and Engineering A, 528 (2011) 1402–1408.
[15]
A. Imandoust, A. Zarei-Hanzaki, M. Sabet and H. R. Abedi, An analysis of the deformation characteristics of a dual phase twinning-induced plasticity steel in warm working temperature regime, Materials and Design, 40 (2012) 556–561.
[16]
D. Li, Y. Wei, C. Lid, L. Hod, D. Lid and X. In, Effects of High Strain Rate on Properties and Microstructure Evolution of TWIP Steel Subjected to Impact Loading, Journal of Iron and Steel Research, International, 17 (2010) 67-73.
[17]
A. Khosravifard, M. M. Moshksar and R. Ebrahimi, High strain rate torsional testing of a high manganese steel: Design and simulation, Materials and Design, 52 (2013) 495-503.
[18]
A. Gilat, Torsional Kolsky Bar Testing, in ASM Handbook, Vol. 8, Mechanical Testing and Evaluation, ASM International, Materials Park, Ohio, 2000, pp.1134-1162.
[19]
S. Curtze and V. -T. Kuokkala, Dependence of tensile deformation behavior of TWIP steels on stacking fault energy, temperature and strain rate, Acta Materialia, 58 (2010) 5129-5141.
[20]
A. Khosravifard, A. S. Hamada, M. M. Moshksar, R. Ebrahimi, D. A. Porter, L. P. Karjalainen, High temperature deformation behavior of two as-cast high-manganese TWIP steels, Materials Science & Engineering A, 582 (2013) 15-21.
[21]
Z. P. Xiong, X. P. Ren, W. P. Bao, S. X. Li and H. T. Qu, Dynamic mechanical properties of the Fe–30Mn–3Si–4Al TWIP steel after different heat treatments, Materials Science and Engineering A, 530 (2011) 426–431.
[22]
A. Khosravifard, M. M. Moshksar and R. Ebrahimi, Mechanical Behavior of TWIP Steel in High Strain Rate Torsional Test, International Journal of ISSI, 9 (2012) 15-19.
[23]
M. Itabashi and K. Kawata, Carbon content effect on high-strain-rate tensile properties for carbon steels, International Journal of Impact Engineering, 24 (2000) 117-131.
[24]
A. Saeed-Akbari, L. Mosecker, A. Schwedt and W. Bleck, Characterization and Prediction of Flow Behavior in High-Manganese Twinning Induced Plasticity Steels: Part I. Mechanism Maps and Work-Hardening Behavior, Metallurgical and Materials Transactions A, 43 (2012) 1688-1704.
[25]
D. Barbier, N. Gey, S. Allain, N. Bozzolo and M. Humbert, Analysis of the tensile behavior of a TWIP steel based on the texture and microstructure evolutions, Materials Science and Engineering A, 500 (2009) 196–206.
[26]
H. Ding, H. Ding, D. Song, Z. Tang and P. Yang, Strain hardening behavior of a TRIP/TWIP steel with 18.8% Mn, Materials Science and Engineering A, 528 (2011) 868–873.
[27]
I. Gutierrez-Urrutia and D. Raabe, Dislocation and twin substructure evolution during strain hardening of an Fe–22 wt.% Mn–0.6 wt.% C TWIP steel observed by electron channeling contrast imaging, Acta Materialia, 59 (2011) 6449–6462.